Home | Sub Study Area | Electrical and Electrotechnology

Electrical and Electrotechnology

Variable Speed Drives for Electricians

State ID: SC-MIU-V1404

North Metropolitan TAFE is delivering a short course to familiarise you with the capabilities of variable speed drives (VSDs).  These are essential to the world of industrial control. Lifts, conveyors, air conditioners, water treatment and assembly lines are a few of the many applications dependent on this technology. 

How to apply

How to apply

Contact us for more information or to enrol in this hands on electronics short course.

Email: coordinator.balmid@nmtafe.wa.edu.au or phone: 9374 6328 

Delivery location, important dates and study options

Semester 1, 2020

Midland - On Campus

Details

Fees and charges

Units

Overview
When Semester 1, 2020
Where Midland
How On campus
Apply now
Ready to apply for this course? Check out the apply and enrol page for more information.

Semester 2, 2019

Midland - On Campus

Details

Fees and charges

Units

Overview
When Semester 2, 2019
Where Midland
How On campus
Apply now
Ready to apply for this course? Check out the apply and enrol page for more information.

Course enquiry

Please note: This form is only for course enquiries. If you would like to apply or require further application information, please visit our Apply and Enrol page.

Electronics and Arduino Design

State ID: SC-MES-V1405

If you've always liked tinkering, inventing and building gadgets this course will help you get creating.

It is aimed at designing and building DIY electronic projects. You'll gain an understanding of electronic components and circuit theory together with microprocessor programming (via the popular Arduino microcontroller).

You'll cover the basics of building these circuits, helping you on your way to success in the DIY electronics world.

Important information

How to apply

Important information

You'll be given a list of components required for the course.  The cost of these is in addition to the course fee of $370

How to apply

Contact us for more information or to enrol in this hands on electronics short course.

Email: coordinator.balmid@nmtafe.wa.edu.au or phone: 9374 6328 

Delivery location, important dates and study options

Continuous enrolment, 2020

Midland - On Campus

Details

Fees and charges

Units

Overview
When Continuous enrolment
Where Midland
How On campus
Apply now
Ready to apply for this course? Check out the apply and enrol page for more information.

Semester 2, 2019

Midland - On Campus

Details

Fees and charges

Units

Overview
When Semester 2, 2019
Where Midland
How On campus
Apply now
Ready to apply for this course? Check out the apply and enrol page for more information.

Course enquiry

Please note: This form is only for course enquiries. If you would like to apply or require further application information, please visit our Apply and Enrol page.

Radio Communications for Industry

State ID: SC-MES-V1384

This course is aimed at personnel in the mining, oil & gas industry, and in both public and private defence and security sectors.

You'll benefit from this workshop if you are involved in SCADA, instrumentation, process control and other control/monitoring systems roles such as:  

Important information

How to apply

Important information

The delivery format of this course is a combination of online theory and on campus practical component. The practical component can be completed over two half days on campus by appointment.

How to apply

For more information contact us via email: pacintech@nmtafe.wa.edu.au .

Delivery location, important dates and study options

Semester 2, 2019

Midland - on campus

Details

Fees and charges

Units

Overview
When Semester 2, 2019
Where Midland
How On campus
Apply now
Ready to apply for this course? Check out the apply and enrol page for more information.

Course enquiry

Please note: This form is only for course enquiries. If you would like to apply or require further application information, please visit our Apply and Enrol page.

Restricted - Electrical safety testing of electrical cord connected equipment and cord assemblies

National ID: UEESS00098 | State ID: AB670

If you have to undertake testing, tagging and reporting of portable/hand held low voltage electrical equipment using a portable appliance tester (PAT) as part of your role in the workplace then this skill set will equip you with the tools you need. 

Important information

How to apply

Important information

Please note that a current First Aid Certificate is a pre-requisite for this skill set and you will be asked to provide a copy of your certifciate at registration.

How to apply

Click Apply now for more information or to enrol via email.

Delivery location, important dates and study options

Semester 1, 2020

Midland - On Campus

Details

Fees and charges

Units

Overview
When Semester 1, 2020
Where Midland
How On campus
Apply now
Ready to apply for this course? Check out the apply and enrol page for more information.

Semester 2, 2019

Midland - On Campus

Details

Fees and charges

Units

Overview
When Semester 2, 2019
Where Midland
How On campus
Apply now
Ready to apply for this course? Check out the apply and enrol page for more information.

Course enquiry

Please note: This form is only for course enquiries. If you would like to apply or require further application information, please visit our Apply and Enrol page.

Restricted - Attachment of cords/cables and plugs to low voltage three phase electrical equipment

National ID: UEESS00092 | State ID: AC311

Successful completion of this skill set will equip you with the tools you need to be able to attach cords, cables and plugs.
You'll gain the training, skills and knowledge to change a flexible plug or cord and wire up new plugs and sockets.

You'll cover the following units

Important information

How to apply

Important information

Please note that a current First Aid Certificate is a pre-requisite for this skill set and you will be asked to provide a copy of your certifciate at registration.

How to apply

Click Apply now for more information or to enrol via email.

Delivery location, important dates and study options

Semester 1, 2020

Midland - On Campus

Details

Fees and charges

Units

Overview
When Semester 1, 2020
Where Midland
How On campus
Apply now
Ready to apply for this course? Check out the apply and enrol page for more information.

Semester 2, 2019

Midland - On Campus

Details

Fees and charges

Units

Overview
When Semester 2, 2019
Where Midland
How On campus
Apply now
Ready to apply for this course? Check out the apply and enrol page for more information.

Course enquiry

Please note: This form is only for course enquiries. If you would like to apply or require further application information, please visit our Apply and Enrol page.

Install, Commission & Service Type B Gas Appliances Skill Set

State ID: EAA33

Be eligible for a Class I Permit or high level Authorisation from Energy Safety WA

Successful completion of this skill set will equip you with the skills and knowledge to service, maintain, rectify faults, recommission, install and commission Type B gas appliances.

Entrance Requirements

Important information

How to apply

Entrance Requirements

You must hold an Electrical Workers License or a Restricted Electrical License to disconnect and reconnect electrical appliances/apparatus to be resulted and issued with a Statement of Academic Record.

If you do not hold an electrical license upon successful completion of the unit you will be issued with a Certificate of Completion and you will be eligible to apply for a class I Permit or a high-level authorisation allowing for service work similar to an independent licensed gasfitter.

Important information

This course is run over 10 days (two weeks), from 8:00am to 4:30pm.

2020 course dates
Group 1 15/06 - 19/06 & 29/06 - 03/07
Group 2 01/11 - 16/11 & 30/11 - 04/12

How to apply

Click below to register you interest via email

Delivery location, important dates and study options

Semester 1, 2020

Midland - Classroom PartTime Category 1 I Permit Gas Course

Details

Fees and charges

Units

Overview
When Semester 1, 2020
Where Midland
How On campus
Apply now
Ready to apply for this course? Check out the apply and enrol page for more information.

Course enquiry

Please note: This form is only for course enquiries. If you would like to apply or require further application information, please visit our Apply and Enrol page.

Restricted - Attachment of cords and plugs to single phase low voltage electrical equipment

National ID: UEESS00091 | State ID: AC778

Successful completion of this skill set you will give you the tools you need to be able to replace plugs and cords. 
You'll get the training, skills and knowledge to change a flexible plug or cord and wire up new plugs and sockets

You'll cover the following units

UEENEEE101A Apply occupational health and safety regulations, codes and practices in the workplace 
UEENEEP024A Attach cords and plugs to electrical equipment for connection to a single phase 230 volt supply 
enabling you to

Important information

How to apply

Important information

Please note that a current First Aid Certificate is a pre-requisite for this skill set and you will be asked to provide a copy of your certifciate at registration.

How to apply

Click Apply now for more information or to enrol via email

Delivery location, important dates and study options

Semester 1, 2020

Midland - On Campus

Details

Fees and charges

Units

Overview
When Semester 1, 2020
Where Midland
How On campus
Apply now
Ready to apply for this course? Check out the apply and enrol page for more information.

Semester 2, 2019

Midland - On Campus

Details

Fees and charges

Units

Overview
When Semester 2, 2019
Where Midland
How On campus
Apply now
Ready to apply for this course? Check out the apply and enrol page for more information.

Course enquiry

Please note: This form is only for course enquiries. If you would like to apply or require further application information, please visit our Apply and Enrol page.

Data Communications - Install and Modify Performance Data Communication Structured Cabling

National ID: UEESS00052 | State ID: AB672

Technical training to help you become a registered open cabler

This skill set will help you meet the training requirements to become a registered open cabler as required to work with Extra-Low Voltage by the Australian and Communication Media Authority (ACMA).

For more information on requirements to become a registered open cabler visit the ACMA website.

Prerequisites

How to apply

Prerequisites

You will need a current CPR (First Aid) certificate.

To enrol in UEENEEF102A Install and maintain cabling for multiple telecommunication services and UEENEEF104A Install and modify performance data communication copper cabling, you will need to have completed the following prerequisite units:

  • UEENEEE101A Apply occupational health and safety regulations, codes and practices in the workplace
  • UEENEEE102A Fabricate, assemble and dismantle utilities industry components
  • UEENEEE104A Solve problems in DC circuits
  • UEENEEE105A Fix and secure electrotechnology equipment
  • UEENEEE107A Use drawings, diagrams, schedules, standards, codes and specifications
How to apply

Click Apply now to register for this course via email.

Delivery location, important dates and study options

Semester 1, 2020

Balga - On Campus

Details

Fees and charges

Units

Overview
When Semester 1, 2020
Where Balga
How On campus
Apply now
Ready to apply for this course? Check out the apply and enrol page for more information.

Semester 2, 2019

Balga - Skill Set

Details

Fees and charges

Units

Overview
When Semester 2, 2019
Where Balga
How On campus
Apply now
Ready to apply for this course? Check out the apply and enrol page for more information.
Balga - Skill Set

Details

Fees and charges

Units

Overview
When Semester 2, 2019
Where Balga
How On campus
Apply now
Ready to apply for this course? Check out the apply and enrol page for more information.

Course enquiry

Please note: This form is only for course enquiries. If you would like to apply or require further application information, please visit our Apply and Enrol page.

3 Phase Test and Tag course

State ID: SC-BET-V1345

This course will provide the competency for 3 Phase Electrical Testing (testing 3 Phase appliances, 415V to AS/NZS 3760).

Content

  • Basic 3 Phase Theory
  • How 3 Phase testing differs from single phasetesting
  • Testing procedures
  • Types of 3 Phase testing equipment

A Certificate of Attendance will be issued.

Prerequisites

How to apply

Prerequisites

You need to have successfully completed a Test and Tag course including OHS.

How to apply

Click below to register you interest via email

13 November 2019 12.30pm - 15.30pm Book now

Or call (08) 9207 4316

Delivery location, important dates and study options

This course is currently undergoing delivery planning and information will be available on our website shortly. Check back later, or use the course enquiry form below to have our Client Contact Centre contact you with further information about the next course start, delivery locations and study modes.

Course enquiry

Please note: This form is only for course enquiries. If you would like to apply or require further application information, please visit our Apply and Enrol page.

Security Installer Skill Set

State ID: EAA88

Technical security installer training to meet licencing requirements

This skill set will help you meet the training requirements for a Security Installer’s Licence issued by the WA Police Force.

For more information on the Security Installer’s Licence visit the WA Police Force website.

 

Prerequisites

How to apply

Prerequisites

You will need a current CPR (First Aid) certificate.

To enrol in UEENEEH150A Assemble and set up basic security systems, you will need to have completed the following prerequisite units:

  • UEENEEE101A Apply occupational health and safety regulations, codes and practices in the workplace
  • UEENEEE102A Fabricate, assemble and dismantle utilities industry components
  • UEENEEE105A Fix and secure electrotechnology equipment
  • UEENEEE107A Use drawings, diagrams, schedules, standards, codes and specifications

 

How to apply

Click Apply now for more information or to enrol via email

Delivery location, important dates and study options

Semester 1, 2020

Balga - On Campus

Details

Fees and charges

Units

Overview
When Semester 1, 2020
Where Balga
How On campus
Apply now
Ready to apply for this course? Check out the apply and enrol page for more information.

Semester 2, 2019

Balga - On Campus

Details

Fees and charges

Units

Overview
When Semester 2, 2019
Where Balga
How On campus
Apply now
Ready to apply for this course? Check out the apply and enrol page for more information.

Course enquiry

Please note: This form is only for course enquiries. If you would like to apply or require further application information, please visit our Apply and Enrol page.

Pages